Describes functions to build draft prism topologies from basis shape surfaces. These can be depressions or protrusions. The semantics of draft prism feature creation is based on the construction of shapes: More...

#include <BRepFeat_MakeDPrism.hxx>

Inheritance diagram for BRepFeat_MakeDPrism:

[legend]

Public Member Functions
	BRepFeat_MakeDPrism (const TopoDS_Shape &Sbase, const TopoDS_Face &Pbase, const TopoDS_Face &Skface, const double Angle, const int Fuse, const bool Modify)
	A face Pbase is selected in the shape Sbase to serve as the basis for the draft prism. The draft will be defined by the angle Angle and Fuse offers a choice between:
	BRepFeat_MakeDPrism ()
void	Init (const TopoDS_Shape &Sbase, const TopoDS_Face &Pbase, const TopoDS_Face &Skface, const double Angle, const int Fuse, const bool Modify)
	Initializes this algorithm for building draft prisms along surfaces. A face Pbase is selected in the basis shape Sbase to serve as the basis from the draft prism. The draft will be defined by the angle Angle and Fuse offers a choice between:
void	Add (const TopoDS_Edge &E, const TopoDS_Face &OnFace)
	Indicates that the edge <E> will slide on the face <OnFace>. Raises ConstructionError if the face does not belong to the basis shape, or the edge to the prismed shape.
void	Perform (const double Height)
void	Perform (const TopoDS_Shape &Until)
void	Perform (const TopoDS_Shape &From, const TopoDS_Shape &Until)
	Assigns one of the following semantics.
void	PerformUntilEnd ()
	Realizes a semi-infinite prism, limited by the position of the prism base.
void	PerformFromEnd (const TopoDS_Shape &FUntil)
	Realizes a semi-infinite prism, limited by the face Funtil.
void	PerformThruAll ()
	Builds an infinite prism. The infinite descendants will not be kept in the result.
void	PerformUntilHeight (const TopoDS_Shape &Until, const double Height)
	Assigns both a limiting shape, Until from TopoDS_Shape, and a height, Height at which to stop generation of the prism feature.
void	Curves (NCollection_Sequence< occ::handle< Geom_Curve > > &S) override
occ::handle< Geom_Curve >	BarycCurve () override
void	BossEdges (const int sig)
	Determination of TopEdges and LatEdges. sig = 1 -> TopEdges = FirstShape of the DPrism sig = 2 -> TOpEdges = LastShape of the DPrism.
const NCollection_List< TopoDS_Shape > &	TopEdges ()
	Returns the list of TopoDS Edges of the top of the boss.
const NCollection_List< TopoDS_Shape > &	LatEdges ()
	Returns the list of TopoDS Edges of the bottom of the boss.
Public Member Functions inherited from BRepFeat_Form
const NCollection_List< TopoDS_Shape > &	Modified (const TopoDS_Shape &F) override
	returns the list of generated Faces.
const NCollection_List< TopoDS_Shape > &	Generated (const TopoDS_Shape &S) override
	returns a list of the created faces from the shape .
bool	IsDeleted (const TopoDS_Shape &S) override
	Returns true if the shape S has been deleted.
const NCollection_List< TopoDS_Shape > &	FirstShape () const
	Returns the list of shapes created at the bottom of the created form. It may be an empty list.
const NCollection_List< TopoDS_Shape > &	LastShape () const
	Returns the list of shapes created at the top of the created form. It may be an empty list.
const NCollection_List< TopoDS_Shape > &	NewEdges () const
	Returns a list of the limiting and glueing edges generated by the feature. These edges did not originally exist in the basis shape. The list provides the information necessary for subsequent addition of fillets. It may be an empty list.
const NCollection_List< TopoDS_Shape > &	TgtEdges () const
	Returns a list of the tangent edges among the limiting and glueing edges generated by the feature. These edges did not originally exist in the basis shape and are tangent to the face against which the feature is built. The list provides the information necessary for subsequent addition of fillets. It may be an empty list. If an edge is tangent, no fillet is possible, and the edge must subsequently be removed if you want to add a fillet.
void	BasisShapeValid ()
	Initializes the topological construction if the basis shape is present.
void	GeneratedShapeValid ()
	Initializes the topological construction if the generated shape S is present.
void	ShapeFromValid ()
	Initializes the topological construction if the shape is present from the specified integer on.
void	ShapeUntilValid ()
	Initializes the topological construction if the shape is present until the specified integer.
void	GluedFacesValid ()
	Initializes the topological construction if the glued face is present.
void	SketchFaceValid ()
	Initializes the topological construction if the sketch face is present. If the sketch face is inside the basis shape, local operations such as glueing can be performed.
void	PerfSelectionValid ()
	Initializes the topological construction if the selected face is present.
BRepFeat_StatusError	CurrentStatusError () const
Public Member Functions inherited from BRepBuilderAPI_MakeShape
virtual void	Build (const Message_ProgressRange &theRange=Message_ProgressRange())
	This is called by Shape(). It does nothing but may be redefined.
virtual const TopoDS_Shape &	Shape ()
	Returns a shape built by the shape construction algorithm. Raises exception StdFail_NotDone if the shape was not built.
	operator TopoDS_Shape ()
Public Member Functions inherited from BRepBuilderAPI_Command
virtual	~BRepBuilderAPI_Command ()
virtual bool	IsDone () const
void	Check () const
	Raises NotDone if done is false.

Additional Inherited Members
Protected Member Functions inherited from BRepFeat_Form
	BRepFeat_Form ()
	Redefines the empty constructor.
void	GlobalPerform ()
	General perform method...
void	UpdateDescendants (const LocOpe_Gluer &G)
void	UpdateDescendants (const BRepAlgoAPI_BooleanOperation &aBOP, const TopoDS_Shape &SResult, const bool SkipFace=false)
bool	TransformShapeFU (const int flag)
Protected Member Functions inherited from BRepBuilderAPI_MakeShape
	BRepBuilderAPI_MakeShape ()
Protected Member Functions inherited from BRepBuilderAPI_Command
	BRepBuilderAPI_Command ()
	Set done to False.
void	Done ()
	Set done to true.
void	NotDone ()
	Set done to false.
Protected Attributes inherited from BRepFeat_Form
bool	myFuse
bool	myModify
NCollection_DataMap< TopoDS_Shape, NCollection_List< TopoDS_Shape >, TopTools_ShapeMapHasher >	myMap
TopoDS_Shape	myFShape
TopoDS_Shape	myLShape
NCollection_List< TopoDS_Shape >	myNewEdges
NCollection_List< TopoDS_Shape >	myTgtEdges
BRepFeat_PerfSelection	myPerfSelection
bool	myJustGluer
bool	myJustFeat
TopoDS_Shape	mySbase
TopoDS_Face	mySkface
TopoDS_Shape	myGShape
TopoDS_Shape	mySFrom
TopoDS_Shape	mySUntil
NCollection_DataMap< TopoDS_Shape, TopoDS_Shape, TopTools_ShapeMapHasher >	myGluedF
Protected Attributes inherited from BRepBuilderAPI_MakeShape
TopoDS_Shape	myShape
NCollection_List< TopoDS_Shape >	myGenerated

Detailed Description

Describes functions to build draft prism topologies from basis shape surfaces. These can be depressions or protrusions. The semantics of draft prism feature creation is based on the construction of shapes:

along a length
up to a limiting face
from a limiting face to a height. The shape defining construction of the draft prism feature can be either the supporting edge or the concerned area of a face. In case of the supporting edge, this contour can be attached to a face of the basis shape by binding. When the contour is bound to this face, the information that the contour will slide on the face becomes available to the relevant class methods. In case of the concerned area of a face, you could, for example, cut it out and move it to a different height which will define the limiting face of a protrusion or depression.

Constructor & Destructor Documentation

◆ BRepFeat_MakeDPrism() [1/2]

BRepFeat_MakeDPrism::BRepFeat_MakeDPrism	(	const TopoDS_Shape &	Sbase,
		const TopoDS_Face &	Pbase,
		const TopoDS_Face &	Skface,
		const double	Angle,
		const int	Fuse,
		const bool	Modify )

inline

A face Pbase is selected in the shape Sbase to serve as the basis for the draft prism. The draft will be defined by the angle Angle and Fuse offers a choice between:

removing matter with a Boolean cut using the setting 0
adding matter with Boolean fusion using the setting 1. The sketch face Skface serves to determine the type of operation. If it is inside the basis shape, a local operation such as glueing can be performed. Initializes the draft prism class

◆ BRepFeat_MakeDPrism() [2/2]

BRepFeat_MakeDPrism::BRepFeat_MakeDPrism ( )

inline

Member Function Documentation

◆ Add()

void BRepFeat_MakeDPrism::Add	(	const TopoDS_Edge &	E,
		const TopoDS_Face &	OnFace )

Indicates that the edge <E> will slide on the face <OnFace>. Raises ConstructionError if the face does not belong to the basis shape, or the edge to the prismed shape.

◆ BarycCurve()

occ::handle< Geom_Curve > BRepFeat_MakeDPrism::BarycCurve ( )

overridevirtual

Implements BRepFeat_Form.

◆ BossEdges()

void BRepFeat_MakeDPrism::BossEdges ( const int sig )

Determination of TopEdges and LatEdges. sig = 1 -> TopEdges = FirstShape of the DPrism sig = 2 -> TOpEdges = LastShape of the DPrism.

◆ Curves()

void BRepFeat_MakeDPrism::Curves ( NCollection_Sequence< occ::handle< Geom_Curve > > & S )

overridevirtual

Implements BRepFeat_Form.

◆ Init()

void BRepFeat_MakeDPrism::Init	(	const TopoDS_Shape &	Sbase,
		const TopoDS_Face &	Pbase,
		const TopoDS_Face &	Skface,
		const double	Angle,
		const int	Fuse,
		const bool	Modify )

Initializes this algorithm for building draft prisms along surfaces. A face Pbase is selected in the basis shape Sbase to serve as the basis from the draft prism. The draft will be defined by the angle Angle and Fuse offers a choice between:

removing matter with a Boolean cut using the setting 0
adding matter with Boolean fusion using the setting 1. The sketch face Skface serves to determine the type of operation. If it is inside the basis shape, a local operation such as glueing can be performed.

◆ LatEdges()

const NCollection_List< TopoDS_Shape > & BRepFeat_MakeDPrism::LatEdges ( )

Returns the list of TopoDS Edges of the bottom of the boss.

◆ Perform() [1/3]

void BRepFeat_MakeDPrism::Perform ( const double Height )

◆ Perform() [2/3]

void BRepFeat_MakeDPrism::Perform	(	const TopoDS_Shape &	From,
		const TopoDS_Shape &	Until )

Assigns one of the following semantics.

to a height Height
to a face Until
from a face From to a height Until. Reconstructs the feature topologically according to the semantic option chosen.

◆ Perform() [3/3]

void BRepFeat_MakeDPrism::Perform ( const TopoDS_Shape & Until )

◆ PerformFromEnd()

void BRepFeat_MakeDPrism::PerformFromEnd ( const TopoDS_Shape & FUntil )

Realizes a semi-infinite prism, limited by the face Funtil.

◆ PerformThruAll()

void BRepFeat_MakeDPrism::PerformThruAll ( )

Builds an infinite prism. The infinite descendants will not be kept in the result.

◆ PerformUntilEnd()

void BRepFeat_MakeDPrism::PerformUntilEnd ( )

Realizes a semi-infinite prism, limited by the position of the prism base.

◆ PerformUntilHeight()

void BRepFeat_MakeDPrism::PerformUntilHeight	(	const TopoDS_Shape &	Until,
		const double	Height )

Assigns both a limiting shape, Until from TopoDS_Shape, and a height, Height at which to stop generation of the prism feature.

◆ TopEdges()

const NCollection_List< TopoDS_Shape > & BRepFeat_MakeDPrism::TopEdges ( )

Returns the list of TopoDS Edges of the top of the boss.

The documentation for this class was generated from the following file:

BRepFeat_MakeDPrism.hxx

Public Member Functions

Additional Inherited Members